2 loadpoints

[profigriller]

I now installed the 2nd loadpoint and I have the problem that only the first loadpoint is shown in the Sunny portal of SMA. Which means it will not be planned.
Most likely I am doing something wrong. Display in evcc is fine

uri: 0.0.0.0:7070 # uri for ui
interval: 30s # control cycle interval
log: trace


chargers:
- name: goalt
  type: go-e
  uri: http://192.168.123.83
- name: gonew
  type: go-e
  uri: http://192.168.123.114


meters:
- name: pvshm
  type: sma
  uri: 192.168.123.59
- name: tripower
  type: modbus
  uri: 192.168.123.98
  id: 126

vehicles:
- name: OutlanderPHEV
  type: default
  title: OutlanderPHEV # display name for UI
  capacity: 10 # kWh
  charge:
    type: http # use script plugin
    uri: http://192.168.123.12:8080/rest/items/OutlanderSOCCalc/state
  cache: 5m # cache duration
- name: LeafEV
  type: carwings
  title: LeafEV # display name for UI
  capacity: 30 # kWh
  user: johndoe@welcome.com # user
  password: XXXXXXXXXXXXXXXX # password
  cache: 20m # cache duration

site:
- title: Home # display name for UI
  meters:
    pv: tripower # pv meter
    grid: pvshm
  
loadpoints:
- title: Garage Outlander # display name for UI
  charger: goalt
  vehicle: OutlanderPHEV
  maxcurrent: 16 # maximum charge current (default 16A)
  phases: 1 # ev phases (default 3)
  mode: pv
  onDisconnect: # set defaults when vehicle disconnects
    #mode: pv # switch back to pv mode
    mode: off # switch back to pv mode
    targetSoC: 90 # charge to 100%
  enable: # pv mode enable behavior
    delay: 2m
    threshold: 3000 # minimum export power (W). If zero, export must exceeds minimum charge power to enable
  disable: # pv mode disable behavior
    delay: 2m
    threshold: 500 # maximum import power (W)
  guardduration: 10m # switch charger contactor not more often than this (default 10m)
  mincurrent: 6 # minimum charge current (default 6A)
  maxcurrent: 16 # maximum charge current (default 16A)
  soc:
    levels: # target soc levels for UI
    - 40
    - 60
    - 80
    - 90
    - 100
- title: Stellplatz Leaf # display name for UI
  charger: gonew
  vehicle: LeafEV
  maxcurrent: 16 # maximum charge current (default 16A)
  phases: 1 # ev phases (default 3)
  mode: pv
  onDisconnect: # set defaults when vehicle disconnects
    #mode: pv # switch back to pv mode
    mode: off # switch back to pv mode
    targetSoC: 90 # charge to 100%
  enable: # pv mode enable behavior
    delay: 2m
    threshold: 3000 # minimum export power (W). If zero, export must exceeds minimum charge power to enable
  disable: # pv mode disable behavior
    delay: 2m
    threshold: 500 # maximum import power (W)
  guardduration: 10m # switch charger contactor not more often than this (default 10m)
  mincurrent: 6 # minimum charge current (default 6A)
  maxcurrent: 16 # maximum charge current (default 16A)
  soc:
    levels: # target soc levels for UI
    - 40
    - 60
    - 80
    - 90
    - 100

hems:
  type: shm
  allowcontrol: true # set true to allow SHM controlling charger in PV modes

[premultiply]

ok, das hab ich noch nie getestet.
Könntest du zur Sicherheit mal noch die Ausgabe der /semp-URL von EVCC posten?

[profigriller]

Wenn ich was testen soll, sag Bescheid. Das läuft bei mir in einem Docker Container.

[profigriller]

gerade gesehen: Bei dem anderen Tool bleiben die letzten beiden digits immer auf 00. Da soll immer die 12 stellige ID inkrementiert werden. In meinem semp.xml sind die sub device ID 00 und 01. Die 12 stellige ID is gleich.

[premultiply]

ja, genau das könnte das Problem hier sein.

[premultiply]

Mach mal ein Issue dazu auf.

[profigriller]

Ok, mach ich