When installing the 6.12.30 kernel, the hyperpixel 4.0 square screen stops working. It was working previously on 6.12.25 (current version in repos).
# For more options and information see
# http://rptl.io/configtxt
# Some settings may impact device functionality. See link above for details
# Uncomment some or all of these to enable the optional hardware interfaces
#dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on
# Enable audio (loads snd_bcm2835)
dtparam=audio=on
# Additional overlays and parameters are documented
# /boot/firmware/overlays/README
# Automatically load overlays for detected cameras
camera_auto_detect=1
# Automatically load overlays for detected DSI displays
display_auto_detect=1
# Automatically load initramfs files, if found
auto_initramfs=1
# Enable DRM VC4 V3D driver
dtoverlay=vc4-kms-v3d
max_framebuffers=2
# Don't have the firmware create an initial video= setting in cmdline.txt.
# Use the kernel's default instead.
disable_fw_kms_setup=1
# Run in 64-bit mode
arm_64bit=1
# Disable compensation for displays with overscan
disable_overscan=1
# Run as fast as firmware / board allows
arm_boost=1
[cm4]
# Enable host mode on the 2711 built-in XHCI USB controller.
# This line should be removed if the legacy DWC2 controller is required
# (e.g. for USB device mode) or if USB support is not required.
otg_mode=1
[cm5]
dtoverlay=dwc2,dr_mode=host
[all]
dtoverlay=vc4-kms-dpi-hyperpixel4sq
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x414fd0b1]
[ 0.000000] Linux version 6.12.30-v8-16k+ (dom@buildbot) (aarch64-linux-gnu-gcc (Ubuntu 11.4.0-1ubuntu1~22.04) 11.4.0, GNU ld (GNU Binutils for Ubuntu) 2.38) #1879 SMP PREEMPT Fri May 23 13:30:44 BST 2025
[ 0.000000] KASLR enabled
[ 0.000000] random: crng init done
[ 0.000000] Machine model: Raspberry Pi Compute Module 5 Lite Rev 1.0
[ 0.000000] efi: UEFI not found.
[ 0.000000] Reserved memory: created CMA memory pool at 0x000000003a000000, size 64 MiB
[ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
[ 0.000000] OF: reserved mem: 0x000000003a000000..0x000000003dffffff (65536 KiB) map reusable linux,cma
[ 0.000000] OF: reserved mem: 0x0000000000000000..0x000000000007ffff (512 KiB) nomap non-reusable atf@0
[ 0.000000] OF: reserved mem: 0x000000003fd16600..0x000000003fd16669 (0 KiB) nomap non-reusable nvram@0
[ 0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x00000003ffffffff]
[ 0.000000] Faking node 0 at [mem 0x0000000000000000-0x000000007fffffff] (2048MB)
[ 0.000000] Faking node 1 at [mem 0x0000000080000000-0x00000000ffffffff] (2048MB)
[ 0.000000] Faking node 2 at [mem 0x0000000100000000-0x000000017fffffff] (2048MB)
[ 0.000000] Faking node 3 at [mem 0x0000000180000000-0x00000001ffffffff] (2048MB)
[ 0.000000] Faking node 4 at [mem 0x0000000200000000-0x000000027fffffff] (2048MB)
[ 0.000000] Faking node 5 at [mem 0x0000000280000000-0x00000002ffffffff] (2048MB)
[ 0.000000] Faking node 6 at [mem 0x0000000300000000-0x000000037fffffff] (2048MB)
[ 0.000000] Faking node 7 at [mem 0x0000000380000000-0x00000003ffffffff] (2048MB)
[ 0.000000] NUMA: Initialized distance table, cnt=8
[ 0.000000] NODE_DATA(0) allocated [mem 0x7fffd200-0x7fffffff]
[ 0.000000] NODE_DATA(1) allocated [mem 0xffffd200-0xffffffff]
[ 0.000000] NODE_DATA(2) allocated [mem 0x17fffd200-0x17fffffff]
[ 0.000000] NODE_DATA(3) allocated [mem 0x1ffffd200-0x1ffffffff]
[ 0.000000] NODE_DATA(4) allocated [mem 0x27fffd200-0x27fffffff]
[ 0.000000] NODE_DATA(5) allocated [mem 0x2ffffd200-0x2ffffffff]
[ 0.000000] NODE_DATA(6) allocated [mem 0x37fffd200-0x37fffffff]
[ 0.000000] NODE_DATA(7) allocated [mem 0x3ff799200-0x3ff79bfff]
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000000000-0x00000000ffffffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal [mem 0x0000000100000000-0x00000003ffffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000000007ffff]
[ 0.000000] node 0: [mem 0x0000000000080000-0x000000003fbfffff]
[ 0.000000] node 0: [mem 0x0000000040000000-0x000000007fffffff]
[ 0.000000] node 1: [mem 0x0000000080000000-0x00000000ffffffff]
[ 0.000000] node 2: [mem 0x0000000100000000-0x000000017fffffff]
[ 0.000000] node 3: [mem 0x0000000180000000-0x00000001ffffffff]
[ 0.000000] node 4: [mem 0x0000000200000000-0x000000027fffffff]
[ 0.000000] node 5: [mem 0x0000000280000000-0x00000002ffffffff]
[ 0.000000] node 6: [mem 0x0000000300000000-0x000000037fffffff]
[ 0.000000] node 7: [mem 0x0000000380000000-0x00000003ffffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000007fffffff]
[ 0.000000] Initmem setup node 1 [mem 0x0000000080000000-0x00000000ffffffff]
[ 0.000000] Initmem setup node 2 [mem 0x0000000100000000-0x000000017fffffff]
[ 0.000000] Initmem setup node 3 [mem 0x0000000180000000-0x00000001ffffffff]
[ 0.000000] Initmem setup node 4 [mem 0x0000000200000000-0x000000027fffffff]
[ 0.000000] Initmem setup node 5 [mem 0x0000000280000000-0x00000002ffffffff]
[ 0.000000] Initmem setup node 6 [mem 0x0000000300000000-0x000000037fffffff]
[ 0.000000] Initmem setup node 7 [mem 0x0000000380000000-0x00000003ffffffff]
[ 0.000000] On node 0, zone DMA: 256 pages in unavailable ranges
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.1 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.2
[ 0.000000] percpu: Embedded 15 pages/cpu s193368 r8192 d44200 u245760
[ 0.000000] pcpu-alloc: s193368 r8192 d44200 u245760 alloc=15*16384
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Detected PIPT I-cache on CPU0
[ 0.000000] CPU features: detected: Virtualization Host Extensions
[ 0.000000] CPU features: detected: Spectre-v4
[ 0.000000] CPU features: detected: Spectre-BHB
[ 0.000000] CPU features: kernel page table isolation forced ON by KASLR
[ 0.000000] CPU features: detected: Kernel page table isolation (KPTI)
[ 0.000000] CPU features: detected: SSBS not fully self-synchronizing
[ 0.000000] alternatives: applying boot alternatives
[ 0.000000] Kernel command line: reboot=w coherent_pool=1M 8250.nr_uarts=1 pci=pcie_bus_safe cgroup_disable=memory numa_policy=interleave nvme.max_host_mem_size_mb=0 numa=fake=8 system_heap.max_order=0 smsc95xx.macaddr=2C:CF:67:FB:43:73 vc_mem.mem_base=0x3fc00000 vc_mem.mem_size=0x40000000 console=ttyAMA10,115200 console=tty1 root=PARTUUID=97df935d-02 rootfstype=ext4 fsck.repair=yes rootwait quiet splash plymouth.ignore-serial-consoles cfg80211.ieee80211_regdom=DE
[ 0.000000] cgroup: Disabling memory control group subsystem
[ 0.000000] mempolicy: NUMA default policy overridden to 'interleave:0-7'
[ 0.000000] Unknown kernel command line parameters "splash", will be passed to user space.
[ 0.000000] Fallback order for Node 0: 0 1 2 3 4 5 6 7
[ 0.000000] Fallback order for Node 1: 1 2 3 4 5 6 7 0
[ 0.000000] Fallback order for Node 2: 2 3 4 5 6 7 0 1
[ 0.000000] Fallback order for Node 3: 3 4 5 6 7 0 1 2
[ 0.000000] Fallback order for Node 4: 4 5 6 7 0 1 2 3
[ 0.000000] Fallback order for Node 5: 5 6 7 0 1 2 3 4
[ 0.000000] Fallback order for Node 6: 6 7 0 1 2 3 4 5
[ 0.000000] Fallback order for Node 7: 7 0 1 2 3 4 5 6
[ 0.000000] Built 8 zonelists, mobility grouping on. Total pages: 1048320
[ 0.000000] Policy zone: Normal
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] software IO TLB: area num 4.
[ 0.000000] software IO TLB: mapped [mem 0x00000000fbffc000-0x00000000ffffc000] (64MB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=8
[ 0.000000] ftrace: allocating 44961 entries in 44 pages
[ 0.000000] ftrace: allocated 44 pages with 3 groups
[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000] rcu: RCU event tracing is enabled.
[ 0.000000] Trampoline variant of Tasks RCU enabled.
[ 0.000000] Rude variant of Tasks RCU enabled.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[ 0.000000] RCU Tasks: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4.
[ 0.000000] RCU Tasks Rude: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4.
[ 0.000000] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4.
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] Root IRQ handler: gic_handle_irq
[ 0.000000] GIC: Using split EOI/Deactivate mode
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] arch_timer: cp15 timer(s) running at 54.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xc743ce346, max_idle_ns: 440795203123 ns
[ 0.000000] sched_clock: 56 bits at 54MHz, resolution 18ns, wraps every 4398046511102ns
[ 0.000092] Console: colour dummy device 80x25
[ 0.000096] printk: legacy console [tty1] enabled
[ 0.000168] Calibrating delay loop (skipped), value calculated using timer frequency.. 108.00 BogoMIPS (lpj=216000)
[ 0.000171] pid_max: default: 32768 minimum: 301
[ 0.000261] LSM: initializing lsm=capability
[ 0.003111] Dentry cache hash table entries: 2097152 (order: 10, 16777216 bytes, vmalloc)
[ 0.004538] Inode-cache hash table entries: 1048576 (order: 9, 8388608 bytes, vmalloc)
[ 0.004602] Mount-cache hash table entries: 32768 (order: 4, 262144 bytes, vmalloc)
[ 0.004640] Mountpoint-cache hash table entries: 32768 (order: 4, 262144 bytes, vmalloc)
[ 0.020021] rcu: Hierarchical SRCU implementation.
[ 0.020027] rcu: Max phase no-delay instances is 1000.
[ 0.020072] Timer migration: 1 hierarchy levels; 8 children per group; 0 crossnode level
[ 0.024349] EFI services will not be available.
[ 0.028027] smp: Bringing up secondary CPUs ...
[ 0.036157] Detected PIPT I-cache on CPU1
[ 0.036194] CPU1: Booted secondary processor 0x0000000100 [0x414fd0b1]
[ 0.044093] Detected PIPT I-cache on CPU2
[ 0.044122] CPU2: Booted secondary processor 0x0000000200 [0x414fd0b1]
[ 0.048152] Detected PIPT I-cache on CPU3
[ 0.048173] CPU3: Booted secondary processor 0x0000000300 [0x414fd0b1]
[ 0.048201] smp: Brought up 8 nodes, 4 CPUs
[ 0.048208] SMP: Total of 4 processors activated.
[ 0.048209] CPU: All CPU(s) started at EL2
[ 0.048212] CPU features: detected: 32-bit EL0 Support
[ 0.048214] CPU features: detected: Data cache clean to the PoU not required for I/D coherence
[ 0.048215] CPU features: detected: Common not Private translations
[ 0.048216] CPU features: detected: CRC32 instructions
[ 0.048219] CPU features: detected: RCpc load-acquire (LDAPR)
[ 0.048220] CPU features: detected: LSE atomic instructions
[ 0.048222] CPU features: detected: Privileged Access Never
[ 0.048223] CPU features: detected: RAS Extension Support
[ 0.048224] CPU features: detected: Speculative Store Bypassing Safe (SSBS)
[ 0.048250] alternatives: applying system-wide alternatives
[ 0.049679] CPU features: detected: Hardware dirty bit management on CPU0-3
[ 0.049850] Memory: 16471072K/16773120K available (13888K kernel code, 2416K rwdata, 4880K rodata, 5632K init, 647K bss, 183120K reserved, 65536K cma-reserved)
[ 0.050055] devtmpfs: initialized
[ 0.051921] Enabled cp15_barrier support
[ 0.051925] Enabled setend support
[ 0.051964] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.051970] futex hash table entries: 1024 (order: 2, 65536 bytes, vmalloc)
[ 0.052089] 2G module region forced by RANDOMIZE_MODULE_REGION_FULL
[ 0.052091] 0 pages in range for non-PLT usage
[ 0.052092] 129332 pages in range for PLT usage
[ 0.052172] pinctrl core: initialized pinctrl subsystem
[ 0.052315] DMI not present or invalid.
[ 0.054641] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.054989] DMA: preallocated 1024 KiB GFP_KERNEL pool for atomic allocations
[ 0.055016] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 0.055046] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ 0.055059] audit: initializing netlink subsys (disabled)
[ 0.055114] audit: type=2000 audit(0.052:1): state=initialized audit_enabled=0 res=1
[ 0.055215] thermal_sys: Registered thermal governor 'step_wise'
[ 0.055223] cpuidle: using governor menu
[ 0.055281] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.055301] ASID allocator initialised with 32768 entries
[ 0.055552] Serial: AMBA PL011 UART driver
[ 0.056231] /soc@107c000000/interrupt-controller@7fff9000: Fixed dependency cycle(s) with /soc@107c000000/interrupt-controller@7fff9000
[ 0.056387] bcm2835-mbox 107c013880.mailbox: mailbox enabled
[ 0.056513] 107d001000.serial: ttyAMA10 at MMIO 0x107d001000 (irq = 16, base_baud = 0) is a PL011 rev3
[ 0.056521] printk: legacy console [ttyAMA10] enabled
[ 0.064052] raspberrypi-firmware soc@107c000000:firmware: Attached to firmware from 2025-05-08T14:13:17, variant start_cd
[ 0.068053] raspberrypi-firmware soc@107c000000:firmware: Firmware hash is 6947117700000000000000000000000000000000
[ 0.072864] /axi/pcie@1000120000/rp1/dpi@148000: Fixed dependency cycle(s) with /spi/display@0
[ 0.073033] /axi/pcie@1000120000/rp1/dpi@148000: Fixed dependency cycle(s) with /spi/display@0
[ 0.076647] bcm2835-dma 1000010000.dma: DMA legacy API manager, dmachans=0x1
[ 0.076897] iommu: Default domain type: Translated
[ 0.076899] iommu: DMA domain TLB invalidation policy: strict mode
[ 0.077044] SCSI subsystem initialized
[ 0.077076] usbcore: registered new interface driver usbfs
[ 0.077083] usbcore: registered new interface driver hub
[ 0.077092] usbcore: registered new device driver usb
[ 0.077167] pps_core: LinuxPPS API ver. 1 registered
[ 0.077168] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.077171] PTP clock support registered
[ 0.077423] vgaarb: loaded
[ 0.077506] clocksource: Switched to clocksource arch_sys_counter
[ 0.077628] VFS: Disk quotas dquot_6.6.0
[ 0.077635] VFS: Dquot-cache hash table entries: 2048 (order 0, 16384 bytes)
[ 0.081100] NET: Registered PF_INET protocol family
[ 0.081446] IP idents hash table entries: 262144 (order: 7, 2097152 bytes, vmalloc)
[ 0.084328] tcp_listen_portaddr_hash hash table entries: 8192 (order: 3, 131072 bytes, vmalloc)
[ 0.084386] Table-perturb hash table entries: 65536 (order: 4, 262144 bytes, vmalloc)
[ 0.084396] TCP established hash table entries: 131072 (order: 6, 1048576 bytes, vmalloc)
[ 0.084735] TCP bind hash table entries: 65536 (order: 7, 2097152 bytes, vmalloc)
[ 0.085420] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.085558] MPTCP token hash table entries: 16384 (order: 4, 393216 bytes, vmalloc)
[ 0.085645] UDP hash table entries: 8192 (order: 4, 262144 bytes, vmalloc)
[ 0.085769] UDP-Lite hash table entries: 8192 (order: 4, 262144 bytes, vmalloc)
[ 0.085933] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.086061] RPC: Registered named UNIX socket transport module.
[ 0.086063] RPC: Registered udp transport module.
[ 0.086064] RPC: Registered tcp transport module.
[ 0.086065] RPC: Registered tcp-with-tls transport module.
[ 0.086066] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.086069] PCI: CLS 0 bytes, default 64
[ 0.086152] Trying to unpack rootfs image as initramfs...
[ 0.094531] kvm [1]: nv: 554 coarse grained trap handlers
[ 0.094620] kvm [1]: IPA Size Limit: 40 bits
[ 0.094637] kvm [1]: GICV region size/alignment is unsafe, using trapping (reduced performance)
[ 0.094677] kvm [1]: vgic interrupt IRQ9
[ 0.094689] kvm [1]: VHE mode initialized successfully
[ 0.194088] Freeing initrd memory: 13104K
[ 0.283796] Initialise system trusted keyrings
[ 0.284068] workingset: timestamp_bits=42 max_order=20 bucket_order=0
[ 0.288420] NFS: Registering the id_resolver key type
[ 0.288426] Key type id_resolver registered
[ 0.288428] Key type id_legacy registered
[ 0.288437] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.288439] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[ 0.288619] Key type asymmetric registered
[ 0.288621] Asymmetric key parser 'x509' registered
[ 0.288641] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[ 0.292682] io scheduler mq-deadline registered
[ 0.292685] io scheduler kyber registered
[ 0.292697] io scheduler bfq registered
[ 0.293015] irq_brcmstb_l2: registered L2 intc (/soc@107c000000/interrupt-controller@7d510600, parent irq: 27)
[ 0.293050] irq_brcmstb_l2: registered L2 intc (/soc@107c000000/interrupt-controller@7c502000, parent irq: 28)
[ 0.293077] irq_brcmstb_l2: registered L2 intc (/soc@107c000000/intc@7d508380, parent irq: 29)
[ 0.293106] irq_brcmstb_l2: registered L2 intc (/soc@107c000000/intc@7d508400, parent irq: 30)
[ 0.293135] irq_brcmstb_l2: registered L2 intc (/soc@107c000000/intc@7d503000, parent irq: 31)
[ 0.294010] ledtrig-cpu: registered to indicate activity on CPUs
[ 0.323913] Serial: 8250/16550 driver, 1 ports, IRQ sharing enabled
[ 0.324183] 107d50c000.serial: ttyS0 at MMIO 0x107d50c000 (irq = 33, base_baud = 6000000) is a Broadcom BCM7271 UART
[ 0.324219] serial serial0: tty port ttyS0 registered
[ 0.324451] iproc-rng200 107d208000.rng: hwrng registered
[ 0.324480] vc-mem: phys_addr:0x00000000 mem_base=0x3fc00000 mem_size:0x40000000(1024 MiB)
[ 0.324656] bcm2712-iommu-cache 1000005b00.iommuc: bcm2712_iommu_cache_probe
[ 0.325946] brd: module loaded
[ 0.326783] loop: module loaded
[ 0.326872] bcm2835-power bcm2835-power: Broadcom BCM2835 power domains driver
[ 0.326962] Loading iSCSI transport class v2.0-870.
[ 0.327636] usbcore: registered new interface driver lan78xx
[ 0.327643] usbcore: registered new interface driver smsc95xx
[ 0.327689] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[ 0.327703] dwc_otg: FIQ enabled
[ 0.327705] dwc_otg: NAK holdoff enabled
[ 0.327706] dwc_otg: FIQ split-transaction FSM enabled
[ 0.327708] Module dwc_common_port init
[ 0.327814] usbcore: registered new interface driver uas
[ 0.327821] usbcore: registered new interface driver usb-storage
[ 0.327887] mousedev: PS/2 mouse device common for all mice
[ 0.335399] rpi-rtc soc@107c000000:rpi_rtc: registered as rtc0
[ 0.336785] rpi-rtc soc@107c000000:rpi_rtc: setting system clock to 2025-06-01T06:51:39 UTC (1748760699)
[ 0.337059] bcm2835-wdt bcm2835-wdt: Poweroff handler already present!
[ 0.337061] bcm2835-wdt bcm2835-wdt: Broadcom BCM2835 watchdog timer
[ 0.339055] sdhci: Secure Digital Host Controller Interface driver
[ 0.339057] sdhci: Copyright(c) Pierre Ossman
[ 0.339087] sdhci-pltfm: SDHCI platform and OF driver helper
[ 0.339152] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping ....
[ 0.339161] hid: raw HID events driver (C) Jiri Kosina
[ 0.339178] usbcore: registered new interface driver usbhid
[ 0.339180] usbhid: USB HID core driver
[ 0.339456] hw perfevents: enabled with armv8_cortex_a76 PMU driver, 7 (0,8000003f) counters available
[ 0.339660] NET: Registered PF_PACKET protocol family
[ 0.339680] Key type dns_resolver registered
[ 0.343091] registered taskstats version 1
[ 0.343152] Loading compiled-in X.509 certificates
[ 0.344537] Demotion targets for Node 0: null
[ 0.344539] Demotion targets for Node 1: null
[ 0.344540] Demotion targets for Node 2: null
[ 0.344541] Demotion targets for Node 3: null
[ 0.344542] Demotion targets for Node 4: null
[ 0.344543] Demotion targets for Node 5: null
[ 0.344544] Demotion targets for Node 6: null
[ 0.344545] Demotion targets for Node 7: null
[ 0.344692] Key type .fscrypt registered
[ 0.344694] Key type fscrypt-provisioning registered
[ 0.345541] brcm-pcie 1000110000.pcie: host bridge /axi/pcie@1000110000 ranges:
[ 0.345547] brcm-pcie 1000110000.pcie: No bus range found for /axi/pcie@1000110000, using [bus 00-ff]
[ 0.345558] brcm-pcie 1000110000.pcie: MEM 0x1b80000000..0x1bffffffff -> 0x0080000000
[ 0.345564] brcm-pcie 1000110000.pcie: MEM 0x1800000000..0x1b7fffffff -> 0x0400000000
[ 0.345571] brcm-pcie 1000110000.pcie: IB MEM 0x0000000000..0x0fffffffff -> 0x1000000000
[ 0.345575] brcm-pcie 1000110000.pcie: IB MEM 0x1000131000..0x1000131fff -> 0xfffffff000
[ 0.346917] brcm-pcie 1000110000.pcie: PCI host bridge to bus 0001:00
[ 0.346920] pci_bus 0001:00: root bus resource [bus 00-ff]
[ 0.346923] pci_bus 0001:00: root bus resource [mem 0x1b80000000-0x1bffffffff] (bus address [0x80000000-0xffffffff])
[ 0.346926] pci_bus 0001:00: root bus resource [mem 0x1800000000-0x1b7fffffff pref] (bus address [0x400000000-0x77fffffff])
[ 0.346936] pci 0001:00:00.0: [14e4:2712] type 01 class 0x060400 PCIe Root Port
[ 0.346942] pci 0001:00:00.0: PCI bridge to [bus 00]
[ 0.346945] pci 0001:00:00.0: bridge window [mem 0x00000000-0x000fffff]
[ 0.346948] pci 0001:00:00.0: bridge window [mem 0x00000000-0x000fffff 64bit pref]
[ 0.346963] pci 0001:00:00.0: PME# supported from D0 D3hot
[ 0.347546] pci 0001:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.449508] brcm-pcie 1000110000.pcie: clkreq-mode set to default
[ 0.449510] brcm-pcie 1000110000.pcie: link up, 5.0 GT/s PCIe x1 (!SSC)
[ 0.449530] pci 0001:01:00.0: [1e4b:1202] type 00 class 0x010802 PCIe Endpoint
[ 0.449546] pci 0001:01:00.0: BAR 0 [mem 0x00000000-0x00003fff 64bit]
[ 0.449648] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.449686] pci 0001:01:00.0: 4.000 Gb/s available PCIe bandwidth, limited by 5.0 GT/s PCIe x1 link at 0001:00:00.0 (capable of 31.504 Gb/s with 8.0 GT/s PCIe x4 link)
[ 0.449779] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01
[ 0.449787] pci 0001:00:00.0: bridge window [mem 0x1b80000000-0x1b800fffff]: assigned
[ 0.449790] pci 0001:01:00.0: BAR 0 [mem 0x1b80000000-0x1b80003fff 64bit]: assigned
[ 0.449798] pci 0001:00:00.0: PCI bridge to [bus 01]
[ 0.449800] pci 0001:00:00.0: bridge window [mem 0x1b80000000-0x1b800fffff]
[ 0.449803] pci_bus 0001:00: resource 4 [mem 0x1b80000000-0x1bffffffff]
[ 0.449805] pci_bus 0001:00: resource 5 [mem 0x1800000000-0x1b7fffffff pref]
[ 0.449807] pci_bus 0001:01: resource 1 [mem 0x1b80000000-0x1b800fffff]
[ 0.449810] pci 0001:00:00.0: Max Payload Size set to 512/ 512 (was 128), Max Read Rq 512
[ 0.449817] pci 0001:01:00.0: Max Payload Size set to 512/ 512 (was 128), Max Read Rq 512
[ 0.449870] pcieport 0001:00:00.0: enabling device (0000 -> 0002)
[ 0.449898] pcieport 0001:00:00.0: PME: Signaling with IRQ 38
[ 0.449942] pcieport 0001:00:00.0: AER: enabled with IRQ 38
[ 0.450052] nvme nvme0: pci function 0001:01:00.0
[ 0.450060] nvme 0001:01:00.0: enabling device (0000 -> 0002)
[ 0.459229] hwmon hwmon1: temp1_input not attached to any thermal zone
[ 0.459246] hwmon hwmon1: temp2_input not attached to any thermal zone
[ 0.459260] hwmon hwmon1: temp3_input not attached to any thermal zone
[ 0.459262] nvme nvme0: min host memory (16 MiB) above limit (0 MiB).
[ 0.463098] nvme nvme0: 4/0/0 default/read/poll queues
[ 0.465885] nvme nvme0: Ignoring bogus Namespace Identifiers
[ 0.469918] nvme0n1: p1 p2
[ 0.470083] brcm-pcie 1000120000.pcie: host bridge /axi/pcie@1000120000 ranges:
[ 0.470087] brcm-pcie 1000120000.pcie: No bus range found for /axi/pcie@1000120000, using [bus 00-ff]
[ 0.470093] brcm-pcie 1000120000.pcie: MEM 0x1f00000000..0x1ffffffffb -> 0x0000000000
[ 0.470097] brcm-pcie 1000120000.pcie: MEM 0x1c00000000..0x1effffffff -> 0x0400000000
[ 0.470103] brcm-pcie 1000120000.pcie: IB MEM 0x1f00000000..0x1f003fffff -> 0x0000000000
[ 0.470108] brcm-pcie 1000120000.pcie: IB MEM 0x0000000000..0x0fffffffff -> 0x1000000000
[ 0.470111] brcm-pcie 1000120000.pcie: IB MEM 0x1000130000..0x1000130fff -> 0xfffffff000
[ 0.471261] brcm-pcie 1000120000.pcie: PCI host bridge to bus 0002:00
[ 0.471265] pci_bus 0002:00: root bus resource [bus 00-ff]
[ 0.471267] pci_bus 0002:00: root bus resource [mem 0x1f00000000-0x1ffffffffb] (bus address [0x00000000-0xfffffffb])
[ 0.471269] pci_bus 0002:00: root bus resource [mem 0x1c00000000-0x1effffffff pref] (bus address [0x400000000-0x6ffffffff])
[ 0.471279] pci 0002:00:00.0: [14e4:2712] type 01 class 0x060400 PCIe Root Port
[ 0.471284] pci 0002:00:00.0: PCI bridge to [bus 00]
[ 0.471287] pci 0002:00:00.0: bridge window [mem 0x1f80000000-0x1fbfffffff]
[ 0.471302] pci 0002:00:00.0: PME# supported from D0 D3hot
[ 0.471915] pci 0002:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.573508] brcm-pcie 1000120000.pcie: clkreq-mode set to default
[ 0.573510] brcm-pcie 1000120000.pcie: link up, 5.0 GT/s PCIe x4 (!SSC)
[ 0.573528] pci 0002:01:00.0: [1de4:0001] type 00 class 0x020000 PCIe Endpoint
[ 0.573541] pci 0002:01:00.0: BAR 0 [mem 0xffffc000-0xffffffff]
[ 0.573546] pci 0002:01:00.0: BAR 1 [mem 0xffc00000-0xffffffff]
[ 0.573552] pci 0002:01:00.0: BAR 2 [mem 0xffff0000-0xffffffff]
[ 0.573614] pci 0002:01:00.0: supports D1
[ 0.573616] pci 0002:01:00.0: PME# supported from D0 D1 D3hot D3cold
[ 0.581513] pci_bus 0002:01: busn_res: [bus 01-ff] end is updated to 01
[ 0.581522] pci 0002:00:00.0: bridge window [mem 0x1f00000000-0x1f005fffff]: assigned
[ 0.581525] pci 0002:01:00.0: BAR 1 [mem 0x1f00000000-0x1f003fffff]: assigned
[ 0.581529] pci 0002:01:00.0: BAR 2 [mem 0x1f00400000-0x1f0040ffff]: assigned
[ 0.581533] pci 0002:01:00.0: BAR 0 [mem 0x1f00410000-0x1f00413fff]: assigned
[ 0.581537] pci 0002:00:00.0: PCI bridge to [bus 01]
[ 0.581539] pci 0002:00:00.0: bridge window [mem 0x1f00000000-0x1f005fffff]
[ 0.581541] pci_bus 0002:00: resource 4 [mem 0x1f00000000-0x1ffffffffb]
[ 0.581543] pci_bus 0002:00: resource 5 [mem 0x1c00000000-0x1effffffff pref]
[ 0.581545] pci_bus 0002:01: resource 1 [mem 0x1f00000000-0x1f005fffff]
[ 0.581548] pci 0002:00:00.0: Max Payload Size set to 256/ 512 (was 128), Max Read Rq 512
[ 0.581555] pci 0002:01:00.0: Max Payload Size set to 256/ 256 (was 128), Max Read Rq 512
[ 0.581606] pcieport 0002:00:00.0: enabling device (0000 -> 0002)
[ 0.581628] pcieport 0002:00:00.0: PME: Signaling with IRQ 44
[ 0.581670] pcieport 0002:00:00.0: AER: enabled with IRQ 44
[ 0.581726] rp1 0002:01:00.0: bar0 len 0x4000, start 0x1f00410000, end 0x1f00413fff, flags, 0x40200
[ 0.581729] rp1 0002:01:00.0: bar1 len 0x400000, start 0x1f00000000, end 0x1f003fffff, flags, 0x40200
[ 0.581737] rp1 0002:01:00.0: enabling device (0000 -> 0002)
[ 0.582355] rp1 0002:01:00.0: chip_id 0x20001927
[ 0.586439] genirq: irq_chip rp1_irq_chip did not update eff. affinity mask of irq 106
[ 0.601162] macb 1f00100000.ethernet eth0: Cadence GEM rev 0x00070109 at 0x1f00100000 irq 112 (2c:cf:67:fb:43:73)
[ 0.601939] dw_axi_dmac_platform 1f00188000.dma: DesignWare AXI DMA Controller, 8 channels
[ 0.602160] xhci-hcd xhci-hcd.0: xHCI Host Controller
[ 0.602165] xhci-hcd xhci-hcd.0: new USB bus registered, assigned bus number 1
[ 0.602596] xhci-hcd xhci-hcd.0: hcc params 0x0240fe6d hci version 0x110 quirks 0x0000808000000810
[ 0.602604] xhci-hcd xhci-hcd.0: irq 137, io mem 0x1f00200000
[ 0.602660] xhci-hcd xhci-hcd.0: xHCI Host Controller
[ 0.602663] xhci-hcd xhci-hcd.0: new USB bus registered, assigned bus number 2
[ 0.602665] xhci-hcd xhci-hcd.0: Host supports USB 3.0 SuperSpeed
[ 0.602703] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.12
[ 0.602705] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.602707] usb usb1: Product: xHCI Host Controller
[ 0.602709] usb usb1: Manufacturer: Linux 6.12.30-v8-16k+ xhci-hcd
[ 0.602711] usb usb1: SerialNumber: xhci-hcd.0
[ 0.602795] hub 1-0:1.0: USB hub found
[ 0.602807] hub 1-0:1.0: 2 ports detected
[ 0.602893] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.12
[ 0.602896] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.602897] usb usb2: Product: xHCI Host Controller
[ 0.602899] usb usb2: Manufacturer: Linux 6.12.30-v8-16k+ xhci-hcd
[ 0.602900] usb usb2: SerialNumber: xhci-hcd.0
[ 0.602959] hub 2-0:1.0: USB hub found
[ 0.602968] hub 2-0:1.0: 1 port detected
[ 0.603182] xhci-hcd xhci-hcd.1: xHCI Host Controller
[ 0.603185] xhci-hcd xhci-hcd.1: new USB bus registered, assigned bus number 3
[ 0.603609] xhci-hcd xhci-hcd.1: hcc params 0x0240fe6d hci version 0x110 quirks 0x0000808000000810
[ 0.603616] xhci-hcd xhci-hcd.1: irq 142, io mem 0x1f00300000
[ 0.603668] xhci-hcd xhci-hcd.1: xHCI Host Controller
[ 0.603670] xhci-hcd xhci-hcd.1: new USB bus registered, assigned bus number 4
[ 0.603672] xhci-hcd xhci-hcd.1: Host supports USB 3.0 SuperSpeed
[ 0.603696] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.12
[ 0.603698] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.603700] usb usb3: Product: xHCI Host Controller
[ 0.603702] usb usb3: Manufacturer: Linux 6.12.30-v8-16k+ xhci-hcd
[ 0.603703] usb usb3: SerialNumber: xhci-hcd.1
[ 0.603766] hub 3-0:1.0: USB hub found
[ 0.603777] hub 3-0:1.0: 2 ports detected
[ 0.603855] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.12
[ 0.603858] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.603859] usb usb4: Product: xHCI Host Controller
[ 0.603861] usb usb4: Manufacturer: Linux 6.12.30-v8-16k+ xhci-hcd
[ 0.603862] usb usb4: SerialNumber: xhci-hcd.1
[ 0.603918] hub 4-0:1.0: USB hub found
[ 0.603927] hub 4-0:1.0: 1 port detected
[ 0.604010] /spi/display@0: Fixed dependency cycle(s) with /axi/pcie@1000120000/rp1/dpi@148000
[ 0.604033] /axi/pcie@1000120000/rp1/dpi@148000: Fixed dependency cycle(s) with /spi/display@0
[ 0.604705] bcm2712-iommu 1000005100.iommu: bcm2712_iommu_init: DEBUG_INFO = 0x20804774
[ 0.605064] bcm2712-iommu 1000005100.iommu: bcm2712_iommu_probe: Success
[ 0.605443] bcm2712-iommu 1000005200.iommu: bcm2712_iommu_init: DEBUG_INFO = 0x20804774
[ 0.605823] bcm2712-iommu 1000005200.iommu: bcm2712_iommu_probe: Success
[ 0.606270] bcm2712-iommu 1000005280.iommu: bcm2712_iommu_init: DEBUG_INFO = 0x20804774
[ 0.606615] bcm2712-iommu 1000005280.iommu: bcm2712_iommu_probe: Success
[ 0.606934] mmc0: CQHCI version 5.10
[ 0.607129] mmc1: CQHCI version 5.10
[ 0.609589] of_cfs_init
[ 0.609622] of_cfs_init: OK
[ 0.609703] clk: Disabling unused clocks
[ 0.618303] PM: genpd: Disabling unused power domains
[ 0.645097] mmc0: SDHCI controller on 1000fff000.mmc [1000fff000.mmc] using ADMA 64-bit
[ 0.753144] mmc0: new ultra high speed SDR104 SDHC card at address 0001
[ 0.753310] mmcblk0: mmc0:0001 SD 14.6 GiB
[ 0.754284] mmcblk0: p1 p2
[ 0.754352] mmcblk0: mmc0:0001 SD 14.6 GiB
[ 0.792043] mmc1: SDHCI controller on 1001100000.mmc [1001100000.mmc] using ADMA 64-bit
[ 0.794896] Freeing unused kernel memory: 5632K
[ 0.794969] Run /init as init process
[ 0.794971] with arguments:
[ 0.794972] /init
[ 0.794974] splash
[ 0.794975] with environment:
[ 0.794975] HOME=/
[ 0.794976] TERM=linux
[ 0.822481] mmc1: new ultra high speed DDR50 SDIO card at address 0001
[ 1.075154] EXT4-fs (mmcblk0p2): mounted filesystem d6ecfcd5-2703-41bf-9301-10c403b6fb0c ro with ordered data mode. Quota mode: none.
[ 1.375614] NET: Registered PF_INET6 protocol family
[ 1.375943] Segment Routing with IPv6
[ 1.375950] In-situ OAM (IOAM) with IPv6
[ 1.404218] systemd[1]: systemd 252.38-1~deb12u1 running in system mode (+PAM +AUDIT +SELINUX +APPARMOR +IMA +SMACK +SECCOMP +GCRYPT -GNUTLS +OPENSSL +ACL +BLKID +CURL +ELFUTILS +FIDO2 +IDN2 -IDN +IPTC +KMOD +LIBCRYPTSETUP +LIBFDISK +PCRE2 -PWQUALITY +P11KIT +QRENCODE +TPM2 +BZIP2 +LZ4 +XZ +ZLIB +ZSTD -BPF_FRAMEWORK -XKBCOMMON +UTMP +SYSVINIT default-hierarchy=unified)
[ 1.404229] systemd[1]: Detected architecture arm64.
[ 1.413392] systemd[1]: Hostname set to <raspberrypi>.
[ 1.701876] systemd[1]: Queued start job for default target graphical.target.
[ 1.725972] systemd[1]: Created slice system-getty.slice - Slice /system/getty.
[ 1.726173] systemd[1]: Created slice system-modprobe.slice - Slice /system/modprobe.
[ 1.726336] systemd[1]: Created slice system-serial\x2dgetty.slice - Slice /system/serial-getty.
[ 1.726496] systemd[1]: Created slice system-systemd\x2dfsck.slice - Slice /system/systemd-fsck.
[ 1.726595] systemd[1]: Created slice user.slice - User and Session Slice.
[ 1.726645] systemd[1]: Started systemd-ask-password-wall.path - Forward Password Requests to Wall Directory Watch.
[ 1.726767] systemd[1]: Set up automount proc-sys-fs-binfmt_misc.automount - Arbitrary Executable File Formats File System Automount Point.
[ 1.726787] systemd[1]: Expecting device dev-disk-by\x2dpartuuid-97df935d\x2d01.device - /dev/disk/by-partuuid/97df935d-01...
[ 1.726794] systemd[1]: Expecting device dev-dri-card0.device - /dev/dri/card0...
[ 1.726800] systemd[1]: Expecting device dev-dri-renderD128.device - /dev/dri/renderD128...
[ 1.726807] systemd[1]: Expecting device dev-ttyAMA10.device - /dev/ttyAMA10...
[ 1.726830] systemd[1]: Reached target integritysetup.target - Local Integrity Protected Volumes.
[ 1.726855] systemd[1]: Reached target nss-user-lookup.target - User and Group Name Lookups.
[ 1.726876] systemd[1]: Reached target slices.target - Slice Units.
[ 1.726893] systemd[1]: Reached target swap.target - Swaps.
[ 1.726913] systemd[1]: Reached target veritysetup.target - Local Verity Protected Volumes.
[ 1.727009] systemd[1]: Listening on systemd-fsckd.socket - fsck to fsckd communication Socket.
[ 1.727063] systemd[1]: Listening on systemd-initctl.socket - initctl Compatibility Named Pipe.
[ 1.727260] systemd[1]: Listening on systemd-journald-audit.socket - Journal Audit Socket.
[ 1.727346] systemd[1]: Listening on systemd-journald-dev-log.socket - Journal Socket (/dev/log).
[ 1.727432] systemd[1]: Listening on systemd-journald.socket - Journal Socket.
[ 1.728192] systemd[1]: Listening on systemd-udevd-control.socket - udev Control Socket.
[ 1.728263] systemd[1]: Listening on systemd-udevd-kernel.socket - udev Kernel Socket.
[ 1.728366] systemd[1]: dev-hugepages.mount - Huge Pages File System was skipped because of an unmet condition check (ConditionPathExists=/sys/kernel/mm/hugepages).
[ 1.728885] systemd[1]: Mounting dev-mqueue.mount - POSIX Message Queue File System...
[ 1.729588] systemd[1]: Mounting sys-kernel-debug.mount - Kernel Debug File System...
[ 1.730238] systemd[1]: Mounting sys-kernel-tracing.mount - Kernel Trace File System...
[ 1.730365] systemd[1]: auth-rpcgss-module.service - Kernel Module supporting RPCSEC_GSS was skipped because of an unmet condition check (ConditionPathExists=/etc/krb5.keytab).
[ 1.732525] systemd[1]: Starting fake-hwclock.service - Restore / save the current clock...
[ 1.733330] systemd[1]: Starting keyboard-setup.service - Set the console keyboard layout...
[ 1.734223] systemd[1]: Starting kmod-static-nodes.service - Create List of Static Device Nodes...
[ 1.735239] systemd[1]: Starting modprobe@configfs.service - Load Kernel Module configfs...
[ 1.736328] systemd[1]: Starting modprobe@dm_mod.service - Load Kernel Module dm_mod...
[ 1.737488] systemd[1]: Starting modprobe@drm.service - Load Kernel Module drm...
[ 1.738649] systemd[1]: Starting modprobe@efi_pstore.service - Load Kernel Module efi_pstore...
[ 1.739829] systemd[1]: Starting modprobe@fuse.service - Load Kernel Module fuse...
[ 1.740875] systemd[1]: Starting modprobe@loop.service - Load Kernel Module loop...
[ 1.741038] systemd[1]: systemd-fsck-root.service - File System Check on Root Device was skipped because of an unmet condition check (ConditionPathExists=!/run/initramfs/fsck-root).
[ 1.742903] systemd[1]: Starting systemd-journald.service - Journal Service...
[ 1.757293] systemd[1]: Starting systemd-modules-load.service - Load Kernel Modules...
[ 1.758260] systemd[1]: Starting systemd-remount-fs.service - Remount Root and Kernel File Systems...
[ 1.759158] systemd[1]: Starting systemd-udev-trigger.service - Coldplug All udev Devices...
[ 1.760397] systemd[1]: Mounted dev-mqueue.mount - POSIX Message Queue File System.
[ 1.760844] systemd[1]: Mounted sys-kernel-debug.mount - Kernel Debug File System.
[ 1.760894] fuse: init (API version 7.41)
[ 1.761100] systemd[1]: Mounted sys-kernel-tracing.mount - Kernel Trace File System.
[ 1.764929] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@lists.linux.dev
[ 1.765203] systemd[1]: Finished kmod-static-nodes.service - Create List of Static Device Nodes.
[ 1.767581] systemd[1]: modprobe@configfs.service: Deactivated successfully.
[ 1.767687] systemd[1]: Finished modprobe@configfs.service - Load Kernel Module configfs.
[ 1.767873] systemd[1]: modprobe@dm_mod.service: Deactivated successfully.
[ 1.767948] systemd[1]: Finished modprobe@dm_mod.service - Load Kernel Module dm_mod.
[ 1.768117] systemd[1]: modprobe@efi_pstore.service: Deactivated successfully.
[ 1.768187] systemd[1]: Finished modprobe@efi_pstore.service - Load Kernel Module efi_pstore.
[ 1.768341] systemd[1]: modprobe@fuse.service: Deactivated successfully.
[ 1.768412] systemd[1]: Finished modprobe@fuse.service - Load Kernel Module fuse.
[ 1.768559] systemd[1]: modprobe@loop.service: Deactivated successfully.
[ 1.768631] systemd[1]: Finished modprobe@loop.service - Load Kernel Module loop.
[ 1.769358] systemd[1]: Mounting sys-fs-fuse-connections.mount - FUSE Control File System...
[ 1.770108] systemd[1]: Mounting sys-kernel-config.mount - Kernel Configuration File System...
[ 1.770228] systemd[1]: systemd-repart.service - Repartition Root Disk was skipped because no trigger condition checks were met.
[ 1.771339] systemd[1]: Mounted sys-fs-fuse-connections.mount - FUSE Control File System.
[ 1.771843] systemd[1]: Mounted sys-kernel-config.mount - Kernel Configuration File System.
[ 1.795034] systemd[1]: Started systemd-journald.service - Journal Service.
[ 1.821371] i2c_dev: i2c /dev entries driver
[ 1.822823] EXT4-fs (mmcblk0p2): re-mounted d6ecfcd5-2703-41bf-9301-10c403b6fb0c r/w. Quota mode: none.
[ 1.849440] systemd-journald[301]: Received client request to flush runtime journal.
[ 2.144348] rpi-gpiomem 107d508500.gpiomem: window base 0x107d508500 size 0x00000040
[ 2.144911] rp1: module is already loaded
[ 2.144984] rpi-gpiomem 107d508500.gpiomem: initialised 1 regions as /dev/gpiomem1
[ 2.145126] rpi-gpiomem 107d517c00.gpiomem: window base 0x107d517c00 size 0x00000040
[ 2.145496] rpi-gpiomem 107d517c00.gpiomem: initialised 1 regions as /dev/gpiomem2
[ 2.145685] rpi-gpiomem 107d504100.gpiomem: window base 0x107d504100 size 0x00000020
[ 2.145825] rpi-gpiomem 107d504100.gpiomem: initialised 1 regions as /dev/gpiomem3
[ 2.145856] rpi-gpiomem 107d510700.gpiomem: window base 0x107d510700 size 0x00000020
[ 2.147155] rpi-gpiomem 107d510700.gpiomem: initialised 1 regions as /dev/gpiomem4
[ 2.147298] rpi-gpiomem 1f000d0000.gpiomem: window base 0x1f000d0000 size 0x00030000
[ 2.147414] rpi-gpiomem 1f000d0000.gpiomem: initialised 1 regions as /dev/gpiomem0
[ 2.183985] input: pwr_button as /devices/platform/pwr_button/input/input0
[ 2.188892] gpio-579 (i2c@0): enforced open drain please flag it properly in DT/ACPI DSDT/board file
[ 2.188915] gpio-580 (i2c@0): enforced open drain please flag it properly in DT/ACPI DSDT/board file
[ 2.190391] dwc2 1000480000.usb: supply vusb_d not found, using dummy regulator
[ 2.190530] mc: Linux media interface: v0.10
[ 2.190623] dwc2 1000480000.usb: supply vusb_a not found, using dummy regulator
[ 2.191667] brcmstb-i2c 107d508200.i2c: @97500hz registered in interrupt mode
[ 2.191724] i2c-gpio i2c@0: using lines 579 (SDA) and 580 (SCL)
[ 2.192033] brcmstb-i2c 107d508280.i2c: @97500hz registered in interrupt mode
[ 2.241461] dwc2 1000480000.usb: DWC OTG Controller
[ 2.241472] dwc2 1000480000.usb: new USB bus registered, assigned bus number 5
[ 2.241479] dwc2 1000480000.usb: irq 174, io mem 0x1000480000
[ 2.242029] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.12
[ 2.242036] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.242038] usb usb5: Product: DWC OTG Controller
[ 2.242040] usb usb5: Manufacturer: Linux 6.12.30-v8-16k+ dwc2_hsotg
[ 2.242042] usb usb5: SerialNumber: 1000480000.usb
[ 2.242384] videodev: Linux video capture interface: v2.00
[ 2.246182] hub 5-0:1.0: USB hub found
[ 2.246202] hub 5-0:1.0: 1 port detected
[ 2.273367] pispbe 1000880000.pisp_be: bcm2712_iommu_of_xlate: MMU 1000005100.iommu
[ 2.273375] pispbe 1000880000.pisp_be: bcm2712_iommu_probe_device: MMU 1000005100.iommu
[ 2.273380] pispbe 1000880000.pisp_be: bcm2712_iommu_device_group: MMU 1000005100.iommu
[ 2.273385] pispbe 1000880000.pisp_be: Adding to iommu group 0
[ 2.273389] pispbe 1000880000.pisp_be: bcm2712_iommu_attach_dev: MMU 1000005100.iommu
[ 2.279471] pispbe 1000880000.pisp_be: Runtime PM usage count underflow!
[ 2.279632] rpi-hevc-dec 1000800000.codec: bcm2712_iommu_of_xlate: MMU 1000005100.iommu
[ 2.279637] rpi-hevc-dec 1000800000.codec: bcm2712_iommu_probe_device: MMU 1000005100.iommu
[ 2.279643] rpi-hevc-dec 1000800000.codec: bcm2712_iommu_device_group: MMU 1000005100.iommu
[ 2.279649] rpi-hevc-dec 1000800000.codec: Adding to iommu group 0
[ 2.279652] rpi-hevc-dec 1000800000.codec: bcm2712_iommu_attach_dev: MMU 1000005100.iommu
[ 2.290394] /axi/pcie@1000120000/rp1/dpi@148000: Fixed dependency cycle(s) with /spi/display@0
[ 2.293126] /spi/display@0: Fixed dependency cycle(s) with /axi/pcie@1000120000/rp1/dpi@148000
[ 2.306264] rpi-hevc-dec 1000800000.codec: Device registered as /dev/video19
[ 2.322060] v3d 1002000000.v3d: [drm] Transparent Hugepage support is recommended for optimal performance on this platform!
[ 2.358830] [drm] Initialized v3d 1.0.0 for 1002000000.v3d on minor 0
[ 2.362181] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 2.368234] Bluetooth: Core ver 2.22
[ 2.368274] NET: Registered PF_BLUETOOTH protocol family
[ 2.368277] Bluetooth: HCI device and connection manager initialized
[ 2.368284] Bluetooth: HCI socket layer initialized
[ 2.368288] Bluetooth: L2CAP socket layer initialized
[ 2.368293] Bluetooth: SCO socket layer initialized
[ 2.368631] Loaded X.509 cert 'benh@debian.org: 577e021cb980e0e820821ba7b54b4961b8b4fadf'
[ 2.368851] Loaded X.509 cert 'romain.perier@gmail.com: 3abbc6ec146e09d1b6016ab9d6cf71dd233f0328'
[ 2.369135] Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 2.369347] Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600'
[ 2.396272] Bluetooth: HCI UART driver ver 2.3
[ 2.396280] Bluetooth: HCI UART protocol H4 registered
[ 2.396306] Bluetooth: HCI UART protocol Three-wire (H5) registered
[ 2.396409] hci_uart_bcm serial0-0: supply vbat not found, using dummy regulator
[ 2.396452] hci_uart_bcm serial0-0: supply vddio not found, using dummy regulator
[ 2.397332] Bluetooth: HCI UART protocol Broadcom registered
[ 2.421839] brcmfmac: F1 signature read @0x18000000=0x15264345
[ 2.424029] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
[ 2.424172] usbcore: registered new interface driver brcmfmac
[ 2.516792] tdo_y17p spi11.0: supply power not found, using dummy regulator
[ 2.533520] usb 5-1: new full-speed USB device number 2 using dwc2
[ 2.637314] edt_ft5x06 13-0048: supply vcc not found, using dummy regulator
[ 2.637382] edt_ft5x06 13-0048: supply iovcc not found, using dummy regulator
[ 2.638720] brcmfmac: brcmf_c_process_txcap_blob: no txcap_blob available (err=-2)
[ 2.639779] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/6 wl0: Aug 29 2023 01:47:08 version 7.45.265 (28bca26 CY) FWID 01-b677b91b
[ 2.651376] input: 13-0048 EP0110M09 as /devices/platform/i2c@0/i2c-13/13-0048/input/input1
[ 2.673561] vc4_hvs 107c580000.hvs: bcm2712_iommu_of_xlate: MMU 1000005200.iommu
[ 2.673573] vc4_hvs 107c580000.hvs: bcm2712_iommu_probe_device: MMU 1000005200.iommu
[ 2.673581] vc4_hvs 107c580000.hvs: bcm2712_iommu_device_group: MMU 1000005200.iommu
[ 2.673601] vc4_hvs 107c580000.hvs: Adding to iommu group 1
[ 2.673608] vc4_hvs 107c580000.hvs: bcm2712_iommu_attach_dev: MMU 1000005200.iommu
[ 2.677301] vc4-drm axi:gpu: bcm2712_iommu_of_xlate: MMU 1000005200.iommu
[ 2.677309] vc4-drm axi:gpu: bcm2712_iommu_probe_device: MMU 1000005200.iommu
[ 2.678837] vc4-drm axi:gpu: bcm2712_iommu_device_group: MMU 1000005200.iommu
[ 2.679117] vc4-drm axi:gpu: Adding to iommu group 1
[ 2.679137] vc4-drm axi:gpu: bcm2712_iommu_attach_dev: MMU 1000005200.iommu
[ 2.681760] vc4-drm axi:gpu: bound 107c580000.hvs (ops vc4_hvs_ops [vc4])
[ 2.682908] Registered IR keymap rc-cec
[ 2.682947] rc rc0: vc4-hdmi-0 as /devices/platform/soc@107c000000/107c701400.hdmi/rc/rc0
[ 2.682985] input: vc4-hdmi-0 as /devices/platform/soc@107c000000/107c701400.hdmi/rc/rc0/input2
[ 2.684963] input: vc4-hdmi-0 HDMI Jack as /devices/platform/soc@107c000000/107c701400.hdmi/sound/card0/input3
[ 2.686316] vc4-drm axi:gpu: bound 107c701400.hdmi (ops vc4_hdmi_ops [vc4])
[ 2.688693] Registered IR keymap rc-cec
[ 2.688750] rc rc1: vc4-hdmi-1 as /devices/platform/soc@107c000000/107c706400.hdmi/rc/rc1
[ 2.688843] input: vc4-hdmi-1 as /devices/platform/soc@107c000000/107c706400.hdmi/rc/rc1/input4
[ 2.692764] input: vc4-hdmi-1 HDMI Jack as /devices/platform/soc@107c000000/107c706400.hdmi/sound/card1/input5
[ 2.693925] vc4-drm axi:gpu: bound 107c706400.hdmi (ops vc4_hdmi_ops [vc4])
[ 2.694120] vc4-drm axi:gpu: bound 107c500000.mop (ops vc4_txp_ops [vc4])
[ 2.694259] vc4-drm axi:gpu: bound 107c501000.moplet (ops vc4_txp_ops [vc4])
[ 2.694400] vc4-drm axi:gpu: bound 107c410000.pixelvalve (ops vc4_crtc_ops [vc4])
[ 2.694475] vc4-drm axi:gpu: bound 107c411000.pixelvalve (ops vc4_crtc_ops [vc4])
[ 2.695767] [drm] Initialized vc4 0.0.0 for axi:gpu on minor 1
[ 2.698910] vc4-drm axi:gpu: [drm] Cannot find any crtc or sizes
[ 2.702518] vc4-drm axi:gpu: [drm] Cannot find any crtc or sizes
[ 2.705189] vc4-drm axi:gpu: [drm] Cannot find any crtc or sizes
[ 2.726215] usb 5-1: New USB device found, idVendor=4041, idProduct=0001, bcdDevice= 1.00
[ 2.726222] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.726224] usb 5-1: Product: HACKBerryPiQ20
[ 2.726226] usb 5-1: Manufacturer: ZitaoTech
[ 2.726228] usb 5-1: SerialNumber: vial:f64c2b3c
[ 2.726992] input: ZitaoTech HACKBerryPiQ20 as /devices/platform/axi/1000480000.usb/usb5/5-1/5-1:1.0/0003:4041:0001.0001/input/input6
[ 2.745944] Bluetooth: hci0: BCM: chip id 107
[ 2.746143] Bluetooth: hci0: BCM: features 0x2f
[ 2.747213] Bluetooth: hci0: BCM4345C0
[ 2.747215] Bluetooth: hci0: BCM4345C0 (003.001.025) build 0000
[ 2.749175] Bluetooth: hci0: BCM4345C0 'brcm/BCM4345C0.hcd' Patch
[ 2.893670] hid-generic 0003:4041:0001.0001: input,hidraw0: USB HID v1.11 Keyboard [ZitaoTech HACKBerryPiQ20] on usb-1000480000.usb-1/input0
[ 2.896803] hid-generic 0003:4041:0001.0002: hiddev96,hidraw1: USB HID v1.11 Device [ZitaoTech HACKBerryPiQ20] on usb-1000480000.usb-1/input1
[ 2.899962] input: ZitaoTech HACKBerryPiQ20 Mouse as /devices/platform/axi/1000480000.usb/usb5/5-1/5-1:1.2/0003:4041:0001.0003/input/input7
[ 2.900121] input: ZitaoTech HACKBerryPiQ20 System Control as /devices/platform/axi/1000480000.usb/usb5/5-1/5-1:1.2/0003:4041:0001.0003/input/input8
[ 2.957654] input: ZitaoTech HACKBerryPiQ20 Consumer Control as /devices/platform/axi/1000480000.usb/usb5/5-1/5-1:1.2/0003:4041:0001.0003/input/input9
[ 2.957813] hid-generic 0003:4041:0001.0003: input,hidraw2: USB HID v1.11 Mouse [ZitaoTech HACKBerryPiQ20] on usb-1000480000.usb-1/input2
[ 3.231444] Adding 524272k swap on /var/swap. Priority:-2 extents:3 across:5185536k SS
[ 3.361671] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 3.361679] Bluetooth: BNEP filters: protocol multicast
[ 3.361685] Bluetooth: BNEP socket layer initialized
[ 3.418151] Bluetooth: hci0: BCM: features 0x2f
[ 3.419487] Bluetooth: hci0: BCM43455 37.4MHz Raspberry Pi 3+-0190
[ 3.419489] Bluetooth: hci0: BCM4345C0 (003.001.025) build 0382
[ 3.419769] Bluetooth: hci0: BCM: Using default device address (43:45:c0:00:1f:ac)
[ 3.436565] Bluetooth: MGMT ver 1.23
[ 3.443642] NET: Registered PF_ALG protocol family
[ 4.133264] macb 1f00100000.ethernet eth0: PHY [1f00100000.ethernet-ffffffff:00] driver [Broadcom BCM54213PE] (irq=POLL)
[ 4.133276] macb 1f00100000.ethernet eth0: configuring for phy/rgmii-id link mode
[ 4.138415] macb 1f00100000.ethernet: gem-ptp-timer ptp clock registered.
[ 4.153526] brcmfmac: brcmf_cfg80211_set_power_mgmt: power save enabled
[ 5.948709] Bluetooth: RFCOMM TTY layer initialized
[ 5.948723] Bluetooth: RFCOMM socket layer initialized
[ 5.948733] Bluetooth: RFCOMM ver 1.11
Describe the bug
When installing the 6.12.30 kernel, the hyperpixel 4.0 square screen stops working. It was working previously on 6.12.25 (current version in repos).
Similar, but not identical to #6871.
Steps to reproduce the behaviour
rpi-updateDevice (s)
Raspberry Pi CM5 Lite
System
uname -a
Before update:
Linux raspberrypi 6.12.25+rpt-rpi-2712 #1 SMP PREEMPT Debian 1:6.12.25-1+rpt1 (2025-04-30) aarch64 GNU/LinuxAfter switching to newer kernel:
Linux raspberrypi 6.12.30-v8-16k+ #1879 SMP PREEMPT Fri May 23 13:30:44 BST 2025 aarch64 GNU/LinuxLogs
config.txt
dmesg
KMSXX
kmsprint
kmstest
no output
pinctrl
sudo pinctrl getAdditional context
No response